钢材注释Comments

注释Comments

*1化学分析Chemical  analysis:0:熔炼分析Ladle  analysis,1:成品分析Product  analysis. 

*2试样位置Sample  location:T:头HEAD,B:尾TAIL;1:钢板角部a conner of the plate,2:钢板板宽1/4位置1/4 width from the Longitudinal edge of the plate,3:钢板板宽1/2位置1/2 width from the Longitudinal edge of the plate,4:钢板距离板边200mm 200mm from the Longitudinal edge of the plate,5:钢板板宽3/4位置3/4 width from the Longitudinal edge of the plate,7:钢板板宽1/3位置1/3 width from the Longitudinal edge of the plate.

p:正火+回火+【中厚钢板】模拟焊后Normalized+Tempered+Max simulative  PWHT,q:正火+回火+最小模拟焊后Normalized+Tempered+Min  simulative  PWHT,[:正火+【中厚钢板】模拟焊后Normalized+Max simulative PWHT,]:正火+最小模拟焊后Normalized+Min simulative  PWHT,e:热成型+正火+最小模焊Thermoforming+Normalized+Min  simulative  PWHT,g:回火+模拟焊后 Tempered+Simulative  PWHT,i:正火+正火+模拟焊后Normalized+Normalized+Simulative   PWHT,s:热成型+正火Thermoforming+Normalized,$:淬火+回火Quenched+Tempered.      *4试验方向Test   piece  orientation:L:纵向Longitudinal,C:横向Transverse,Z:Z 向Through-thickness.*5屈服类型Yield strength type:2:Rp0.2,3:ReL,4:ReH,5:Rt0.5,6:Re.

*6厚内位置Position  of  specimen:0:原厚Original  thickness,1:面下1mm Below the surface,2:面下2mm Below the surface,5:面下1.6mm Below the surface,6:1/4 of the thickness,7:1/2 of the thickness,8:1/3 of the thickness,9:留一个轧制面,减薄至12mm Reserve a rolling surface,thinning to 12mm,a:表面下0.5mm以下below 0.5mm from surface,b:距表面2mm以内,中心线和板厚的1/4重合0~2mm from surface,superposition of centerline and 1/4 thickness position,A:上表面三点The upper surface 3 points,B:上下表面各三点 The upper surface 3 points and lower surface 3 points,C:1/2 of the thickness,D:留一

轧制面Reserve a rolling surface,E:面下1.5mm below the surface,F:面下12.5mm below the surface,G:上下表面及四个断面各三点The upper surface,lower surface and four sections are 3 points each,H:试样上下表面，两侧边缘上、中、下各三点 the upper and lower surfaces of the sample,and the upper,middle and bottom of the two sides of the sample test 3 points each,

I:两侧边缘上、中、下各三点The upper,middle and bottom of the two sides of the sample test 3 points each,J:上下表面、板厚1 / 4、1 / 2、3 / 4各一点The upper surface,lower surface and thickness of

1 / 4,1 / 2,3 / 4 each of 1 point,K:上表面一点The upper surface 1 point,L:下表面一点The lower surface 1 point,M:上下表面各一点The upper surface, lower surface each 1 point,N:上下表面头、中、尾各三点The upper surface,the lower surface of the head, the middle, the end three points,P:上1/4The upper 1/4 of thickness,Q:下1/4The lower 1/4 of thickness,V:试样上、下表面及四个端面各打三点The upper surface, the lower surface and the four end faces of the sample are three points,X:厚度1/2处1/2 of  thickness,Y:钢板表面头、中、尾Head, middle and tail of steel platseu     rface.

*7硬度测量位置Hardness test location:0:上表面+下表面The upper and lower surfaces,1:上表面The upper surface,2:侧面Side,3:1/4厚度1/4thickness position,4:1/2厚度1/2thickness position,5:3/4厚度3/4 thickness  position,6:四个侧面4 sides,7:下表面The  lower  surface,8:1/3厚度1/3thickness  position,9:全厚The  entire  thickness,A:上表右侧上On the head end of right side,the upper surface,B:上表右侧中On the middle position of right side,the upper surface,C:上表右侧下On the tail end of right side,the upper surface,D:上表左侧上On the head end of leG side,the upper surface,E:上表左侧中On the middle position of leG side,the upper surface,F:上表左侧下On the tail end of leG side,the upper surface,G:下表右侧上On the head end of right side,the lower surface,H:下表右侧中On the middle position of right side,the lower surface,I:下表右侧下On the tail end of right side,the lower surface,J:下表左侧上On the head end of leG side,the lower surface,K:下表左侧中On the middle position of leG side,the lower

surface,

L:下表左侧下On the tail end of leG side,the lower surface,M:全厚度三点Three points of the entire thickness,N:沿钢板长度方向二侧边缘的头部中部底部的上下表面各打3点Three points respectively at upper surface and lower surface of head end,middle position,tail end on both sides along plate length ,O:沿试样两侧边缘上中下各测3点Three points each at top, middle and bottom positions along both sides of specimen,P:表面下2mm below the surface,

Q:试样上下表面各打3点3points at upper surface and 3 points lower surface of the sample,R:试样上下表面及四个厚度端面The upper surface,lower surface and four sides,S:沿钢板两侧边缘上中下各测3点Three points each at top, middle and bottom position along both sides of steel plate,T:1/2和1/4厚度1/2 and 1/4 thickness position,U:表面下1.6mm below the surface,V:表面5点5 points surface,W:沿试样长度方向二侧边缘的头,中,底部的上,下表面各打3点

Three points respectively at upper surface and lower surface of head end, middle position,tail end on both sides along specimen length ,X:距离边缘一个厚度位置,钢板4角上,下表面各3点Three poinsts respectively at upper surface and lower surface of four corners with a distance to the edge equal to nominal thickness,@:上下表面（每个面含靠近钢板四个角部各1处,钢板中间1处,每处3点)Thirty readings shall be taken in total. 3 each from the 4 corner and middle osfueach rface.

*3试样状态Condition of test piece:0:交货状态Delivery status,1:【中厚钢板】模拟焊后Max simulative PWHT,2:最小模拟焊后Min simulative PWHT,3:调质Quenching tempered,4,:模拟焊后Simulative PWHT,5:热成型Thermoforming,6:正火Normalized,7:回火Tempered,8:淬火Quenching,9:正火+回火Normalized+Tempered,D:热成型+模拟焊后Thermoforming+Simulative  PWHT,E:热成型+【中厚钢板】模拟焊后Thermoforming+Max simulative  PWHT,F:热成型+最小模拟焊后Thermoforming+Min  simulative   PWHT,H:正火+回火+模拟焊后Normalized+Tempered+Simulative   PWHT,I:热成型+正火+回火Thermoforming+Normalized+Tempered,P:正 火+模拟焊后Normalized+Simulative   PWHT,S:热成型+正火+回火+模拟焊后Thermoforming+Normalized+Tempered+Simulative   PWHT,V:热成型+正火+模拟焊后Thermoforming+Normalized+Simulative    PWHT,X:热 成型+正火+回火+【中厚钢板】模拟焊后Thermoforming+Normalized+Tempered+Max simulative PWHT,Y:热成型+正火+回火+最小模拟焊后Thermoforming+Normalized+Tempered+Min simulative PWHT,d:热成型+正火

+【中厚钢板】模焊Thermoforming+Normalized+Max simulative PWHT,!:交货态+(正火+【中厚钢板】模拟焊后)Delivery status+（Normalized+Max simulative PWHT）,#:交货态+(正火+最小模拟焊后)+(正火+【中厚钢板】模拟焊后) Delivery status+（Normalized+Min simulative PWHT）+（Normalized+Max simulative PWHT）,&:(【中厚钢板】模拟焊后+步冷脆化SC)（Max simulative PWHT +Step Cooling）,(:(热成型+热成型+正火)

（Thermoforming+Thermoforming+Normalized）,):(热成型+热成型+正火+【中厚钢板】模拟焊后)（Thermoforming+Thermoforming+Normalized+Max    simulative    PWHT）,*:【中厚钢板】模拟焊后+（【中厚钢板】模拟焊后+步冷脆化SC）Max simulative PWHT+（Max simulative PWHT +Step Cooling）,+:（淬火+回火+模拟焊后）（Quenched+Tempered+Simulative PWHT）,-:(热成型+正火+回火+【中厚钢板】模拟焊后+步冷)

（Thermoforming+Normalized+Tempered+Max simulative PWHT +Step Cooling）,/:（热成型+淬火+回火）（Thermoforming+Quenched+Tempered）,

::（热成型+淬火+回火+最小模拟焊后）（Thermoforming+Quenched+Tempered+Min simulative PWHT）,;:（热成型+淬火+回火+【中厚钢板】模拟焊后）（Thermoforming+Quenched+Tempered+Masximu lative PWHT）,<:回火+【中厚钢板】模拟焊后Tempered+Max simulative PWHT,=:(热成型+热成型+正火+最小模拟焊后)（Thermoforming+Thermoforming+Normalized+Min simulative PWHT）,>:回火+最小模拟焊后Tempered+Min simulative PWHT,@:(热成型+正火+回火+【中厚钢板】模拟焊后)+（热成型+正火+回火+【中厚钢板】模拟焊后+步冷）（Thermoforming+Normalized+Tempered+Max simulative PWHT）+

（Thermoforming+Normalized+Tempered+Max simulative PWHT +Step Cooling）,A:交货态+模拟焊后Delivery  status+Simulative  PWHT,B:交货态+【中厚钢板】模拟焊后+最小模拟焊后Delivery status+Masxim  ulative PWHT+Min simulative  PWHT,C:SR1+SR2Max  simulative  PWHT+Min  simulative  PWHT,G:最小模拟焊后+(最小模拟焊后+步冷)Min simulative  PWHT+（Min simulative PWHT+Step Cooling）,J:交货态+（热成型+模拟焊后）Delivery status+（Thermoforming+Simulative PWHT）,K:交货态+（热成型+【中厚钢板】模拟焊后）+（热成型+最小模拟焊后）Delivery status+（Thermoforming+Max simulative PWHT）+

（Thermoforming+Min simulative PWHT）,L:(最小模拟焊后+步冷）（Min simulative PWHT +Step Cooling）,M:交货态+调质Delivery status+Quenching tempered,N:交货态+热成型Delivery status+Thermoforming,O:模拟焊后+（模拟焊后+步冷）Simulative PWHT+（Simulative PWHT+Step Cooling）,Q:交货态+（正火＋模拟焊后）Delivery status+（Normalized+Simulative  PWHT）,R:交货态+

（正火+回火）Delivery   status+（Normalized+Tempered）,T:交货态+（热成型+正火+回火+模拟焊后）Delivery   status+（Thermoforming+Normalized+Tempered+Simulative   PWHT）,U:(热成型+正火+【中厚钢板】模焊)+(热成型+正火+最小模焊)（Thermoforming+Normalized+Max simulative PWHT）+（Thermoforming+Normalized+Min simulative PWHT）,

Comments W:交货态+（热成型+正火+模拟焊后）Delivery status+（Thermoforming+Normalized+Simulative PWHT）,Z:交货态+(正火+回火+【中厚钢板】模拟焊后)+(正火+回火+最小模拟焊后)Delivery status+

（Normalized+Tempered+Max simulative PWHT）+（Normalized+Tempered+Min simulative PWHT）,:交货态+（热成型+淬火+回火+模拟焊后）Delivery status+

（Thermoforming+Quenched+Tempered+Simulative  PWHT）,a:交货态+【中厚钢板】模拟焊后(SR1)Delivery  status+Max  simulative  PWHT,b:交货态+最小模拟焊后(SR2)Delivery  status+Min  simulative  PWHT,c:(热成型+正火+回火)+(热成型+正火+回火+【中厚钢板】模拟焊后)（Thermoforming+Normalized+Tempered）+（Thermoforming+Normalized+Tempered+Max simulative PWHT）,f:(热成型+正火+回火)+(热成型+正火+回火

+SR1)+( 热 成 型 + 正 火 + 回 火 +SR2)（Thermoforming+Normalized+Tempered）+（Thermoforming+Normalized+Tempered+Max simulative PWHT）+（Thermoforming+Normalized+Tempered+Min simulative PWHT）,h:交货态+（回火+模拟焊后）Delivery status+(Tempered+Simulative  PWHT),j:交货态+（正火+正火+模拟焊后）Delivery  status+(Normalized+Normalized+Simulative  PWHT),k:交货态+（正火+回火+ 模拟焊后）Delivery status+(Normalized+Tempered+Simulative PWHT),l:（模拟焊后+步冷）（Simulative PWHT+Step Cooling）,m:交货态+（热成型+正火+回火+最小模拟焊后）Delivery status+

（Thermoforming+Normalized+Tempered+Min simulative PWHT）,n:交货态+（热成型+正火+回火+【中厚钢板】模拟焊后）Delivery status+（Thermoforming+Normalized+Tempered+Max simulative PWHT）,o:交货态

+（热成型+正火+回火+最小模拟焊后）+（热成型+正火+回火+【中厚钢板】模拟焊后）Delivery status+（Thermoforming+Normalized+Tempered+Min simulative PWHT）+

（Thermoforming+Normalized+Tempered+Max simulative PWHT）,r:交货态+(热成型+正火)Delivery status+（Thermoforming+Normalized）,t:交货态+(热成型+正火+最小模焊)Delivery status+

（Thermoforming+Normalized+Min simulative PWHT）,s:（热成型+正火）（Thermoforming+Normalized）,

u:(热成型+正火+回火)+(热成型+正火+回火+最小模拟焊后)（Thermoforming+Normalized+Tempered）+（Thermoforming+Normalized+Tempered+Min     simulative     PWHT）,v:(热成型+正火+回火+最小模拟焊后)+(热成型+正火+回火+最小模拟焊后+步冷)（Thermoforming+Normalized+Tempered+Min  simulative   PWHT）+（Thermoforming+Normalized+Tempered+Min   simulative   PWHT+Step   Cooling）,w:(热成型+ 正火+回火+最小模拟焊后+步冷)（Thermoforming+Normalized+Tempered+Min simulative PWHT+Step Cooling）,x:(热成型+正火+回火)+(热成型+正火+回火+模拟焊后)

（Thermoforming+Normalized+Tempered）+（Thermoforming+Normalized+Tempered+Simulative       PWHT）,y:交货态+(热成型+正火+回火)Delivery      status+（Thermoforming+Normalized+Tempered）,z:(热成型+ 正火+回火+【中厚钢板】模拟焊后)+(热成型+正火+回火+最小模拟焊后)（Thermoforming+Normalized+Tempered+Max  simulative   PWHT）+（Thermoforming+Normalized+Tempered+Min   simulative   PWHT）,{:(正火+ 【中厚钢板】模拟焊后)+(正火+最小模拟焊后)（Normalized+Max simulative PWHT）+（Normalized+Min simulative PWHT）,}:交货态+(正火+最小模拟焊后)Delivery status+（Normalized+Min simulative PWHT）,~:

（热成型+淬火+回火+模拟焊后）（Thermoforming+Quenched+Tempered+Simulative    PWHT）,￥:交货态+（淬火+回火+模拟焊后）Delivery   status+（Quenched+Tempered+Simulative    PWHT）,^  交货态+ (热成型+正火+【中厚钢板】模焊)+(热成型+正火+最小模焊)Delivery status+（Thermoforming+Normalized+Max simulative PWHT）+（Thermoforming+Normalized+Min simulative PWHT）